Cm7 Install Issue

Droid2xo

New Member
Joined
Dec 14, 2010
Messages
9
Reaction score
0
Ok so I SBF'd back to stock 2.3.2 . Then downloaded the GB OTA, rooted using Droid 3 root, downloaded the CM7 ROM and used Bootstrap recovery to install it after wiping/factory reset and dalivk. Rebooted it and it goes to the red M logo and shuts off and just repeats. What am I doing wrong?
 
have you done a battery pull?

also i think the cm7 rom should be a cm7 type looking boot up
 
I didn't have the GB CM7 I got if figured out lol.

Sent from my CM7 DROID2 using DroidForums
 
I didn't have the GB CM7 I got if figured out lol.

Sent from my CM7 DROID2 using DroidForums

that was my thought. I was going to make sure you didn't DL from the CM website, because that's based on the Froyo kernel. Glad you figured it out!
 
ha well at least you know what you did wrong,
2 quick questions i am about to sbf my current phone, and receive my replacement today,

what method do you use to sbf &
what method do you use to root
 
ha well at least you know what you did wrong,
2 quick questions i am about to sbf my current phone, and receive my replacement today,

what method do you use to sbf &
what method do you use to root

Both can be found in my signature. Check out the links below

|
|
v
 
0wow thanks which file download , odexed or deodexed ,

also these are basically the steps i think i should follow, please correect me if im wrong

1.) install drivers and rsd program
2.) run rsd program nd follow the steps in the first post

well thats as far as i think i know that i should do?
 
Don't worry about odexed/deodexed just get the full SBF file, then:

1) install drivers and rsd (there's a newer version of rsd in my signature too)
2) get the phone into bootloader mode by powering it off completely, then hold the up key on the physical keyboard when powering on
3) once in bootloader mode, connect to the pc and start rsd
4) select the sbf file in rsd
5) click start and wait for it to reboot

it might not get to 100% before it reboots. I've had it get stuck at 99%, but that doesn't necessarily mean that something went wrong. When it boots:

1) wait until the M shows, pull the battery
2) put the battery back in and boot it up while holding the x key on the keyboard to get into stock recovery
3) when you see the android with the ! press the search button on the keyboard (Pretty sure it's search for Froyo, if search doesn't work, press BOTH volume buttons simultaneously)
4) once in recovery, select "wipe data/factory reset"
5) reboot

At this point you should be at a complete factory state. I did this all from memory, so some things may vary slightly, but all the necessary information should be here. If you need more help, feel free to stop back here in the forums, and feel free to PM me if needed.
 
i cant find the full sbf file,? on MDW it doesnt load up, do you know where else i can get it,
 
thanks, quick question i got my new droid 2, nd it had GB,
so i used the droid life way to root it, but when it barely does it first step in the program (rebooting phone)

it rebooots to im guessing the bootloader page
nd it says

d d2.37


charge ok


nd etc...

how did this happen?

i have to sbf am i correct?
 
no, you don't need to sbf. Unplug the cord, reboot, and as it's booting back into GB plug the cord back in. The root process should finish without having to do anything. It should reboot 3 times total (I think)
 
ok if i understand correctly. i run the program again, nd as soon as the reboot process begins... disconnect it, nd then connect back in after the droid boot screen shows up? nd the program will finish to root it?
 
everytime it booted it it ran into the bootloader, so i did what u said nd it worked!! now im rooted nd im gonna be running galnet till cm9 fixes the camera.

but why does it happen tho?
 
Back
Top